One Minute: Bezel stone earrings

What you will need:

• 2 earring hooks
• 2 matching, pre-bezeled stones from an arts & crafts supply store.
• optional - jump rings (to create more space)
• pliers

Turquoise earrings:
With the pliers slightly open the bottom of the earring enough to slide on the bezeled stone.  Use pliers to close the bottom of the earring.

White and grey earrings:
With the pliers, open a jump ring and connect one grey bezeled stone to one white bezeled stone.  Then close the jump ring tightly.
Using the pliers again, open the bottom of the earring enough to slide on the top of the grey bezeled stone.  Close the bottom of the earring with the pliers.

Summertime bracelets

I am not normally a wearer of bracelets, but when I found this diy, I loved the bright, summery colors used in the bracelets.

So, I made myself two: one with silver fixtures and light blue and coral string.  And the other with gold fixtures and orange and pink string.  What's additionally fun about this diy is the color options are endless!

My two DIY summertime bracelets

Learn how to make for yourself, here.

A variation on bombay hoops

Some of my favorite hoop earrings that I made are these, the bombay hoops.

I made a variation on them, with beads in one of my favorite colors.  Now these are my favorite hoops!:

The how to is very similar to the original bombay hoops.

What you need:

-a pair of wire hoops

-a pair of earring hooks

-a thin wire, 24 or 26 gauge (I used a fun blue wire for these).

-16 beads (8 for each earring).

-pliers

-wire cutters

First, cut a piece of thin wire, about 20 inches long.  Fold one end over the hoop and use the pliers to wrap it around the hoop tightly.

Put a bead onto the wire and loop it through, then loop the wire another 3 times, to keep with the pattern.

Continue this process until all 8 beads are on the hoop.

Be sure to wrap the wire three times after the 8th bead and use the pliers again to tighten it.

Cut the wire closely to the hoop at both ends with the wire cutters and use the pliers to wrap the remaining bit around the hoop.

Use the pliers to connect the top of the hoops.  Slightly open the bottom of each earring hook and connect one to each wire hoop.  Close the bottom of each earring hook.

And all done!

In Pursuit of Suede String & Tassels

As you can see by what I post on this blog, I've recently been making jewelry with tassels.

When I found this picture of suede tassel earrings, the colors appealed to me: thin turquoise suede, ruby red beads and gold fixtures.

Anthropologie faceted fringe drops

As I tried to find materials to make these earrings, I found that the thinness of the suede is a large part of the effect these earrings hold.

So, my first move was to try to cut my thicker strings of suede in half.

I first used an X-Acto knife.. it was very difficult to cut evenly through the suede string with it.

Then I tried using sewing scissor, the sharpest scissors I could imagine.  With much fear for my fingers, I was able to cut the suede string thinner.

...But then the suede string fell apart.

Rather than waste more of the suede string, I just went to the art supplies store and bought thinner suede string.  AND, I also got some thin leather cord - and made two pairs of earrings!

My DIY Earrings.

What you need:

- The thinnest suede or leather cord you can find.

- Very thin wire.

- 2 of the same glass bead.

- 2 head pins with rounded top.

- A pair of earring hooks.

- Round-nose pliers and a wire cutter.

What to do:

1. Place each bead on a separate head pin.

2. Use the round nose pliers to close the head pin into a loop.  Make the loop a bit larger than normal - the suede string needs to go through it.

(The loop you made is pointing downwards)

3. With pliers, add an earring hook to the top of each head pin.

4. Determine the desired length of the tassels for your earrings.  The black pair above are about an inch and a half.  For the tan pair, they are over two inches.

5. Double the length you decide on and cut 3 to 4 pieces.

6. Fold the cut pieces in half and put one end through the loop at the bottom of the bead.

7. Start slowly and tightly wrapping the thin wire around the top of the folded suede.

8. Once you wrap the wire to desired thickness around the suede, cut with the wire cutters, and fold the raw edge in with the pliers.

9. Trim the ends so they are even.

That's all!

Girly pink, edgy spikes

On a recent visit home, I got to spend some much needed time with my jewelry supplies.  For months I had saved pictures of jewelry that I liked in anticipation of my reunion to my bead boxes.

A style of necklace that I started to see a lot involved at least 2 rows of chain, lots of head pins, and a repetitive pattern of beads.

Some examples:

Examples of necklaces with the 2+ chain style, from my Pinterest board.

With the second necklace in mind especially, I selected the beads and chains I liked best for my DIY necklace.

My DIY Necklace

What you need:
- A chain with small links
- 14 flat headed head pins in the same color as the chain.
- 4 different types of beads in increasing sizes, 14 of each.
- Spikes or other elongating bead (tear drop, leaf shape, etc), 14 of each.
- Round-nose pliers and wire cutters.
- Clasp and jump rings

Directions:
1. First, measure out the chain required for each row of the necklace.  I had 14 columns of beads, and I put a space of 3 chain links in between each column.  Therefore, my 3 rows of chains were each 53 links in length.
2. Next, slide one of the smallest beads onto the head pin.
3. Put the head pin with the bead through the first link of the first row.
4. Add the next bead of incremental size onto the head pin and put the head pin through the first link of the second row.
5. Add the 2nd largest bead onto the head pin and put the head pin through the first link of the third row.
6. Add the largest bead onto the bead pin and use the round-nose pliers to close the pin.
7. Add the spiked bead to the end of the closed pin with a jump ring.

Repeat steps 2-7.  For this necklace I did steps 2-7 fourteen times and with 3 links in between each head pin / column.

8. Once the bulk of the necklace has been assembled, add a chain to each end of the top row.  Attach a clasp and jump rings to the end of the chain you just added.

All done!

I made my necklace with light pink, turquoise blue and silver beads, and silver spiked beads.  I like the girly, yet edgy feel of the necklace.  Unlike most DIY creations made from pictures, this necklace sits very well on. And I love finding different outfits to pair it with!

Chain of Change

Life is in serious transition mode now.. In all of this change occurring, I am trying to keep in mind the adage,

"Every end is a new beginning."

After a year, I've decided to postpone my return to America and continue living abroad.

Though there are so many changes now, what hasn't changed is my continued search for inspiration and love for DIY :)

I made this jump-ring chain necklace a while ago now and am still waiting for the perfect opportunity to don it.

MariaFrancescaPepe Tubular Chain Bracelet

The inspiration came from a picture I found on Pinterest (of course!) of a MariaFrancescaPepe bracelet.

After studying the picture for awhile to deduce how the jump rings were attached to each other, I set to work.

At its most basic form, all you really need to make this is A LOT of jump rings, pliers (or two pairs to save your fingers!), and a clasp... and patience.

How To:

(I made these pictures in hopes of making the instructions as understandable as possible!)

1. Open a smaller jump ring (or a chain of them or a paper clip) and slide on two jump rings.

2. Open and add two jump rings perpendicularly to the first two grey jump rings.

3. Push the blue jump rings back (so that they are parallel with the smaller jump ring). 

4. Slide the grey jump rings open so they make a 'V' and have the blue jump rings come forward.  Open two more jump rings and attach them to the blue jump rings.

5. Add two more jump rings perpendicular to the green jump rings you just added.  This is the same thing you did in step 2.

6. Push the purple jump rings back (so they are parallel with the blue jump rings.  Again, this is the same as step 3).

7. Slide the green jump rings open so they make a 'V' and have the purple jump rings come forward.

8. Open two more jump rings and attach them to the purple jump rings.

Pretend these two new jump rings are the green jump rings in step 5 and that you now need to add purple jump rings and then light grey jump rings. 

Keep repeating steps 5-8 until you get to your desired length.  Add a smaller jump ring to the end and a clasp.

A beautiful jump ring chain made (hopefully!) easy!

I decided to make a necklace instead of a bracelet - thoughts?

Tri-Color Tassels

Some more tassel earrings! Hurray!

These are super simple DIY earrings made from string and 3 colors of seed beads.

my DIY earrings

What you need:
-2 earring hooks
-2 bead tips
-nylon string (preferably in the color of the lowest color bead, in this case, brown)
-3 colors of seed beads (or more if you'd like).
-needle
-scissors
-pliers

First, cut 10 pieces of nylon string, about 4 to 5 inches each, depending on how long you want the tassle.
Then, string one bead of the last color onto one end of a cut nylon string.  Pull bead to middle and fold in half.
After folding the string in half, you can put a the two string-ends through a needle to make your life easier.  String all the following beads onto the needle so the first bead is stuck at the bottom (and no knot is needed at end to keep the beads on!).
Put as many beads of each color as you like.  Lots of freedom here!
Leave yourself plenty of room at the top.
Make 10 of these beaded strings.
With 5 beaded strings, slip the remaining string through the bead tip.  Knot the tops of the strings well so they cannot slip through the bead tip.  Cut the excess string.  Use the pliers to close the bead tip.
Repeat with the second set of 5 strings.
Use the pliers to open the bottoms of the earring hooks and slip on the bead tips.  Use pliers to close earring hooks.
All done!                   
                                          Wearing my DIY creation:

The most time consuming part of this DIY is definitely stringing all of the seed beads!

Braced with Chain and String

Can't believe it's been over a month since I was home.  And can't believe it's taken me this long to write up another blog post!  Life here is busy to say the least.

Before I went home, I had been seeing these bracelets at fancy stores all over the place.. selling for at least $25 each.  Recognizing that they are just chain, suede string, and some connecting pieces, I of course exclaimed, "wait, I can make this!".

I had been unable to find chain that was thick enough for the purpose of these bracelets at my local craft store.  I therefore waited until my trip to America to really scour the craft stores for the right materials for this project.

The bracelet took under 30 minutes to make; I ended up making a bunch of them!

Here's what you need:
- 2 pieces of chain (about 8-10 inches, depending on your wrist).
- Suede string, 2.5 times the length of your chain.
- lobster clasp and jump rings
- craft glue
- pliers
- scissors

What to do:
1. Using a jump ring, attach the first links of the two chains together.
2. Lay the chains down so that they are flat and the links line up to one another.
3. Start weaving the suede string between the links (in, over, under).
4. Once you've weaved through a few links, glue the tail of the suede string to itself.  (Do this on the side of the bracelet that will face your wrist, so that it will not be seen when you wear it.)
5. Continue weaving the suede string the same way between the links of the two chains.
6. At the end, once again connect the last two links with a jump ring.  Again, glue the suede string to itself on the side facing your wrist.
7. Cut any extra suede string from either side, once the glue has dried.
8. Open one of the jump rings on one end and add a lobster clasp.  Close the jump ring.
9. On the other end, attach as many extra jump rings as necessary to allow ease of putting on the bracelet!

With buying most of the supplies in bulk packs from the craft store, the bracelets ended up only costing a few dollars each!

I ended up keeping one for myself and giving the rest as gifts.  Everyone loved them!

Pearl, Gold, Hoops. And time at home.

My DIY Hoops

I made the long trip home for the recent holiday break.  I've been loving living abroad, but I was missing my sisters, Mom's home-cooked meals, American clothing stores, and of course, my jewelry-making supplies.

I spent a lot of time in A.C. Moore and even more time planning what to make and then making it.

Inspiration: Earrings from here.

Perusing Pinterest, (as I spend many of my hours), I found these gorgeous earrings being sold on an Etsy site.

While I do not have the blue opal gemstone or the pearls as used by the creator of these earrings, I did find some teardrop shaped glass beads and fake pearls

So here's what you need to make your own pair:
- 2 earring hoops
- 24 small pearl beads
- 2 teardrop shaped beads
- 26 head pins
- pliers and wire cutters

3 Easy Steps
1.  Put the each pearl bead and teardrop bead on its own head pin.  Close the head pin with round-nose pliers and cut off any excess wire with the wire cutters.
2.  Slide 6 pearl beads on head pins onto the hoop, add one teardrop bead, and then another six pearl  beads.  Repeat for the other earring.
3.  Use the pliers to turn up the end of the hoops to close.  All done!

Here are my earrings:

Chain, Overlap, Chain.

One of my favorite necklaces on my jewelry tree is a chain and ribbon necklace I got super on-sale from Harrods during my time studying abroad in London.  The necklace is composed of overlapping thick gold chains and a black ribbon to hold it around my neck.

Necklace from 'Bella Shay Fine Fashion Jewelry and Accessories'

I came across the necklace above on Pinterest a few months ago.  It reminded me of the overlapping chains in my Harrod's necklace, but instead with two colors of thin chains, and no ribbon.

Then, over the summer, I found this black chain and this black with gold tint chain for just a few dollars each. 

And proceeded to make my own version of this necklace!

My DIY!

1. I first measured out a piece of black chain to the desired length of the necklace.

2. I cut equal pieces of black chain and gold tinted chain.  The black chain I cut again, in half.  I then attached the three pieces of chain together: black chain --> gold tinted chain --> black chain.

Make 10 of these.

3. I attached the first chain to the left-most spot I wanted, to the middle of the necklace.

4. Repeat this step, but with each new attaching chain, affix the beginning of the chain to every other link in the necklace, and then the end of the chain to every other link after the middle.

From Hemp to Suede...

In continuation of my crafting with suede string, I made this bracelet over the weekend:

When I showed my friends the bracelet, most were immediately reminded of the hemp bracelets popular at summer camps.

There's a reason for this recollection... it's the same stitch!  I believe it is called the square knot..

Materials:

- 4 pieces suede string (2 long and 2 bracelet length)

- 2 end closing pieces

- 32 jump rings, plus a few extra for bracelet closure

- clasp

- pliers

The Square Knot Stitch

Enclose the 4 pieces of string in one of the closing pieces.  Use pliers to tightly close the end piece around the 4 strings.

Begin the square knot (as shown in picture above).  I did 12 or so square knots before I started adding the rings, and the bracelet is a little large on me, but I also have slim wrists.

Add 1 ring to each outer string, and tie the knot.  Tie a second knot after that.  For the third knot, put the strings back through the rings and add another ring on top.  Tie a knot.  Repeat the steps.  I used 16 rings on each side (a total of 32).

After, do the same amount of knots that the bracelet started with, before the rings were added.

Close off the end with another end piece and pliers - make sure it is very tight.  Add the additional rings and the clasp.  

        

I'm thinking of making this with gold fixtures next.. and maybe black suede?

The First Post in a New Place: Suede Tassle Earrings

I'm back!

After 3 months settling into this new place, I have returned to my crafting ways.

With a holiday gift exchange tomorrow - it gave me the perfect excuse to visit the local craft store.  Of course, I bought much more than needed in anticipation of other crafting projects!

I found suede string in a multitude of colors, and for a little less than fifty cents a piece.  Most things are more expensive here; it is always exciting when I come across cheap finds.  So, I bought a bunch of strings, a variety of other trinkets (clasps, earring hooks, elastic, jump rings,...), and set to work.

Materials:

- suede string (cut into 12 pieces, about 2 inches each)

- 2 cylinder cones

- 2 Earring loops

- Industrial strength glue

- pliers

- scissors

Once the suede string is cut into 12 pieces, separate 6 and 6 for each earring.

Gather the bunch of 6 pieces.  Squeeze the glue into one cylinder cone.  Then, push the bunch of suede string into the cylinder cone.  Repeat for the second earring.  Let them sit for a few minutes.

Use the pliers to attach the earring loops to the top of the cylinder cones.

Trim the ends of the suede so they are all the same length.

That's all!

I ended up making 2 pairs - now which color do I keep and which do I give?!

In time for a Photoshoot

On a recent trip, I had a few different special occasions to attend.  The first occasion was a photo shoot with the entire family - we haven't done one of these in years!
Once I picked the outfit and coordinated the color scheme with the rest of the family, I went to look for jewelry to pair with it.  But I couldn't find anything that I liked with the outfit.

So, what else to do, but make a new pair of earrings to match!

I spotted these earrings, the 'Bombay Hoops,' in the Perfect Match book we own and have been meaning to make them for a long time.  This was the perfect occasion.

The gold with the black beads was a good match for my coral and black outfit.  And since it hardly took any time to make, I made a second pair of gold with gold translucent beads for my mom!

It was really simple- all you need are:
- a pair of hoops (you can make your own if you want!)
- a thin wire in the same color as the hoops (24 or 26 gauge)
- 14 glass beads (7 for each earring)
- pliers
- wire cutters

First, cut a piece of thin wire, about 14 inches long.  Fold one end over the hoop and use the pliers to wrap it around the hoop tightly.  I wrapped it 3 times here.  Put a bead onto the wire and loop it through, then loop the wire another 3 times to keep with the pattern.  Continue this process until 7 beads are on hoop, with 3 wire wraps in between.  Wrap the wire the last 3 times after the final bead.  Cut both ends with the wire cutters and use the pliers to wrap the remaining bit around the hoop.
Repeat these steps for the second earring.
This all took me around 20 minutes per pair!

Reminiscent of a Dreamcatcher..

While crafting with my mom in our 'crafting room' (we took over the family room!), we realized we didn't have enough jewelry in neutral colors.  As I love color, I tend to drift towards colorful beads/ribbons/chains...  Recently, I've been obsessed with a dark teal green color.

I spotted the earrings on the right awhile ago and have been meaning to make them for some time now.  Figuring this was my chance to apply my need for neutrals, I made a pair for myself in silver and black!

  My DIY:                                                                          Inspiration:

from Modern Vintage Boutique, $22

I used larger seed beads in my DIY than shown in the original.  Also, I did not make them as long... the original pair are 6 inches! Despite being shorter, I think they still have a nice effect and my younger sister called them 'party earrings'!

Supplies:

-2 earring hoops

-small silver seed beads

-small black seed beads

-30 silver crimp beads

-30 12inch pieces of black string

-needle

-pliers

-scissors

Like most projects, the most time consuming part was stringing all the beads.

On the hoop, I initially slid on 3 silver seed beads.

Before putting the needle on the string, I slid one black bead onto one string.  Then I folded the string in half (so the one bead was at the bottom) and put it through the needle.  I then strung 24 more black beads (25 total).  Since this is the first string, I add 6 silver beads, then the crimp bead.

Position the string on the hoop, swing the needle through so that it is attached to the hoop, and back through the crimp bead and all the way down to the black beads.

Used the pliers to crimp the crimp bead.  Make sure the crimp bead is secure and the string cannot slip through it whatsoever.

Repeat this process.  Here is an image to better show the number of beads I used:

             
I only had time to draw out half the earring.  But, the silver beads increase and then decrease in (from left to right) as follows:
6 --> 7 --> 8 --> 9 --> 10 --> 11 --> 12 --> 13 --> 12 --> 11 --> 10 --> 9 --> 8 --> 7 --> 6

The black beads remain at a constant 25.

Once all 15 strands are on and the crimp beads are pressed tightly, add 3 silver beads to the end, like at the beginning.

Cut the remaining string close to the bead so that it cannot be seen.

That's all!

I made 3 more pairs of earrings this week, but posts for those will have to wait until after vacation.
Now, off to Vancouver!