One Minute: Bezel stone earrings

What you will need:

• 2 earring hooks
• 2 matching, pre-bezeled stones from an arts & crafts supply store.
• optional - jump rings (to create more space)
• pliers

Turquoise earrings:
With the pliers slightly open the bottom of the earring enough to slide on the bezeled stone.  Use pliers to close the bottom of the earring.

White and grey earrings:
With the pliers, open a jump ring and connect one grey bezeled stone to one white bezeled stone.  Then close the jump ring tightly.
Using the pliers again, open the bottom of the earring enough to slide on the top of the grey bezeled stone.  Close the bottom of the earring with the pliers.

A variation on bombay hoops

Some of my favorite hoop earrings that I made are these, the bombay hoops.

I made a variation on them, with beads in one of my favorite colors.  Now these are my favorite hoops!:

The how to is very similar to the original bombay hoops.

What you need:

-a pair of wire hoops

-a pair of earring hooks

-a thin wire, 24 or 26 gauge (I used a fun blue wire for these).

-16 beads (8 for each earring).

-pliers

-wire cutters

First, cut a piece of thin wire, about 20 inches long.  Fold one end over the hoop and use the pliers to wrap it around the hoop tightly.

Put a bead onto the wire and loop it through, then loop the wire another 3 times, to keep with the pattern.

Continue this process until all 8 beads are on the hoop.

Be sure to wrap the wire three times after the 8th bead and use the pliers again to tighten it.

Cut the wire closely to the hoop at both ends with the wire cutters and use the pliers to wrap the remaining bit around the hoop.

Use the pliers to connect the top of the hoops.  Slightly open the bottom of each earring hook and connect one to each wire hoop.  Close the bottom of each earring hook.

And all done!

In Pursuit of Suede String & Tassels

As you can see by what I post on this blog, I've recently been making jewelry with tassels.

When I found this picture of suede tassel earrings, the colors appealed to me: thin turquoise suede, ruby red beads and gold fixtures.

Anthropologie faceted fringe drops

As I tried to find materials to make these earrings, I found that the thinness of the suede is a large part of the effect these earrings hold.

So, my first move was to try to cut my thicker strings of suede in half.

I first used an X-Acto knife.. it was very difficult to cut evenly through the suede string with it.

Then I tried using sewing scissor, the sharpest scissors I could imagine.  With much fear for my fingers, I was able to cut the suede string thinner.

...But then the suede string fell apart.

Rather than waste more of the suede string, I just went to the art supplies store and bought thinner suede string.  AND, I also got some thin leather cord - and made two pairs of earrings!

My DIY Earrings.

What you need:

- The thinnest suede or leather cord you can find.

- Very thin wire.

- 2 of the same glass bead.

- 2 head pins with rounded top.

- A pair of earring hooks.

- Round-nose pliers and a wire cutter.

What to do:

1. Place each bead on a separate head pin.

2. Use the round nose pliers to close the head pin into a loop.  Make the loop a bit larger than normal - the suede string needs to go through it.

(The loop you made is pointing downwards)

3. With pliers, add an earring hook to the top of each head pin.

4. Determine the desired length of the tassels for your earrings.  The black pair above are about an inch and a half.  For the tan pair, they are over two inches.

5. Double the length you decide on and cut 3 to 4 pieces.

6. Fold the cut pieces in half and put one end through the loop at the bottom of the bead.

7. Start slowly and tightly wrapping the thin wire around the top of the folded suede.

8. Once you wrap the wire to desired thickness around the suede, cut with the wire cutters, and fold the raw edge in with the pliers.

9. Trim the ends so they are even.

That's all!

Who Doesn't Like Braids?

I've seen this braided bead necklace on tons of Pinterest boards!
Of course, I had to make it!

The DIY Inspiration

The most time consuming aspect of this necklace was stringing 6 strands of beads (2 for each piece of the braid).

Supplies:

- a lot of 1 bead type

- string

- 6 crimping clasps (also called bead tips?)

- 2 jump rings

- chain

- closing clasp

-pliers

For photo instructions, check out this image.

I went to ACMoore and bought a pack of reddish coral beads for this.  I cut 6 pieces of string, and tied them 2, 2, and 2 (so three strands).  Once I beaded to the desired length, I closed the knots of each 3 strands to separate crimping clasps, on each side (so 6 clasps total). Close the crimping clasps.  Then, braid!!
Once the beads are neatly braided, I combined the 3 closing clasps on the left onto one jump ring, and the 3 clasps on the right onto a second jump ring.
Then, attach the chain to the jump rings on each side.  Open the chain at the top to put on a closing clasp.  All done!

I made a second one in white with gold chain for my mom.  But, it looked great on my sister, so we gave it to her!

Chain + Jump Rings + Beads!

The top, left picture is of an Ann Taylor Loft necklace, priced at $39.95, the photo on the right is the Flamingo Toes DIY of the loft necklace, and the last picture is my own DIY!!

What you need:

- Jump rings in 4 different sizes (for example: extra small, small, medium, large)

- a piece of chain to attach beads (4 to 6 inches)

- a second piece of nicer chain to hang around neck

- 25 or so glass beads in an assortment of colors

- one head pin per bead

- closure and jump rings (to adjust length of necklace)

First, put each glass bead being used on a head pin and close it.  For instructions on doing this, look here.

Then, slide the jump rings into the chain in size order.  I did 15 xsmall --> 20 small --> 25 medium --> 30 large --> 25 medium --> 20 small --> 15 xsmall.  When changing between the sizes, link one jump ring of the larger size into the appropriate place in the chain.  By doing this, the jump rings will stay in place on the chain and won't slide over each other.

With the rings in place, attach the beads on their head pins to the large jump rings in the middle of the necklace.  I didn't attach more than one bead to a jump ring, but I didn't put a bead on every jump ring.  Play around and see what looks nice.. it's easy enough to open the jump ring and move the bead somewhere else!  

If this is confusing, Flamingo Toes has a great tutorial for this necklace here.  It took me about and hour and a half to make this.

I used larger jump rings and larger glass beads in clear and a range of shades of turquoise than other necklaces.  My necklace has a bit more of an African-y feel to it and definitely more of a statement piece, while the original necklace is smaller and more delicate.  The necklace goes really nicely with my tribal print black & white maxi dress.  Also, I just bought teal colored jeans and I can't wait to pair this necklace with them!